A lot of us love to get our pets into the Halloween spirit and with Blend’s Boo Crew fabrics we can do just that. The designs in the fabrics are just so cute. I love the dogs in costumes!

boo crew fabrics

Adding HeatnBond Fleece Fusible High Loft as batting makes a great lightweight wall hanging or table topper. It’s so easy to apply it to fabric! I used HeatnBond EZ Print Lite sheets to create the applique and sewed around the edges, but if you wanted a no-sew applique then use the HeatnBond Ultrahold.

Super Dooper Dog Boo Crew Wall Hanging or Table Topper, by Carol Swift, Just Let Me Quilt

Halloween Boo Crew Applique Quilt with Heatnbond

Halloween Boo Crew Quilt Supplies:

HeatnBond Lite, Iron-on Adhesive

Or HeatnBond EZ Print Lite sheets

HeatnBond Fleece Fusible High Loft

Therm O Web SpraynBond Basting Adhesive

Iron, Fabric

Super Dooper Boo Crew Applique Pattern and Instructions

Cutting instructions:

Cut 1 – 15½” x 15½” square for center block

Cut 2 – 3” x 15 ½” strips for left and right Border A

Cut 2 – 3” x 20 ½” strips for top and bottom Border A

Cut 2 – 1½” x 20½” strips for left and right Border B

Cut 2 – 1½” x 22½” strips for top and bottom Border B

Cut 2 – 3” x 22½” strips for left and right Border C

Cut 2 – 3” x 27½” strips for top and bottom Border C

Cut 2 – 2½” x 27½” strips for left and right Border D

Cut 2 – 2½” x 31½” strips for top and bottom Border D

Cut 1 – Fabric for quilt backing


Boo Crew Dog Halloween Quilt Sewing instructions:

Step 1: Prepare the applique patterns following either of the applique instructions below:

Applique with printable Heat n Bond EZ Print Lite sheets: Using your inkjet printer, print out applique pattern pieces using HeatnBond EZ Print Lite sheets. Load one sheet at a time into the paper tray. Sheet should be placed so printing is on the smooth side of the paper. Print quality at the normal setting and for plain paper. Allow 5-10 seconds for ink to dry.

Applique with Heat n Bond Lite: Trace applique designs on the smooth side of HeatnBond Lite.

boo crew 4

Step 2: Iron adhesive pieces to wrong sides of fabrics with a medium heat iron, no steam. Press for 2 seconds. Repeat until all surfaces have been bonded to fabric. Let cool. Cut out applique pieces. Peel off paper liner.

Step 3: Place applique shapes, adhesive side down, on top of 15½” x 15½” center fabric. Press and hold iron for 6 seconds on each section until entire piece is bonded. Let cool.

boo crew 2

Step 4: Sew around edges using a straight, zig-zag, or blanket stitch.

boo crew 3

Step 5: Sew borders to center block in the order below:

Border A – Sew 3” x 15½” strips to left and right

Border A – Sew 3” x 20½” strips to top and bottom

Border B – Sew 1½” x 20½” strips to left and right

Border B – Sew 1½” x 22½” strips to top and bottom

Border C – Sew 3” x 22½” strips to left and right

Border C – Sew 3” x 27½” strips to top and bottom

Border D – Sew 2½” x 27½” strips to left and right

Border D – Sew 2½” x 31½” strips to top and bottom

Borders

Step 6: Cut fusible interfacing to fit quilt backing. Pre-heat iron to wool (medium heat) setting with steam. Place the rough side of the interfacing onto the back (wrong side) of the quilt back. Cover with a dry pressing cloth. Press and hold iron with medium pressure for 10-15 seconds. Repeat by lifting iron to the new area and pressing, slightly overlapping previous area until entire surface is bonded. Let cool. If more ironing is needed iron an additional 5 seconds from the front of the project.

boo crew 6

Step 7: Protect the area where you will be working by placing an old sheet or paper under and around the area you’ll be spraying. Place the quilt back with interfacing face down on the working surface. Using the SpraynBond Adhesive, spray about 6-8 inches across the interfacing from one edge to the other. Place the wrong side of the quilt back front over the sprayed surface. Smooth fabric to ensure it adheres to the sprayed fabric. Continue this method of spraying and smoothing just 6-8 inches at a time until you reach the bottom of the quilt. Check for creases or folds. Trim edges and square-up quilt.

Step 8: Quilt and add binding as desired.

Those dogs in costumes made the cutest back on this table topper!

boo crew 5

4 Comments on Boo Crew Dog Halloween Quilt Featuring HeatnBond

  1. mary
    October 4, 2017 at 8:58 am (7 years ago)

    That is fabulous. The fabrics are so cute and make for such a great Halloween project.

  2. margessw
    October 9, 2017 at 4:09 pm (7 years ago)

    Wow !! Absolutely awesome!!

2Pingbacks & Trackbacks on Boo Crew Dog Halloween Quilt Featuring HeatnBond